Ubiquiti Networks AF-24 Uživatelská příručka Strana 1

Procházejte online nebo si stáhněte Uživatelská příručka pro Přístupové body WLAN Ubiquiti Networks AF-24. Ubiquiti Networks AF-24 WLAN access point Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - 1.4+ Gbps Radio

24 GHz Point to Point 1.4+ Gbps RadioModel: AF-24

Strany 2

3. Connect the other end of the Ethernet cable from the DATA port to the Ethernet port labeled POE on the GigE PoE Adapter.4. Connect the Power Cord

Strany 3 - Package Contents

airFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings

Strany 4 - Hardware Overview

1. Connect an Ethernet cable from your computer to the CONFIG port on the airFiber AF-24.2. Configure the Ethernet adapter on your computer with a s

Strany 5

5. Click the Wireless tab.6. Enter the Basic Wireless Settings:a. For one airFiber AF-24, select Master from the Wireless Mode drop-down. For the o

Strany 6 - Interfaces

7. Configure the Wireless Security: a. Select the AES Key Type, HEX or ASCII.b. For the Key field: - HEX Enter 16 bytes (eight, 16-bit HEX values:

Strany 7 - Long Flash (3:1 on/off cycle)

Hardware InstallationTo install the airFiber AF-24:1. Insert the four Carriage Bolts into the Pole Mount Bracket.2. Attach the Pole Mount Bracket to

Strany 8 - Installation Overview

3. Loosen, but do NOT remove the eight Lock Bolts located on the Alignment Bracket.4. Ensure that there is a 6 mm gap between the head of each M8x14

Strany 9

5. Lift the airFiber AF-24 and align the four M8x14 Serrated Flange Screws with the slots on the Pole Mount Bracket. Seat the screws in the slots. Se

Strany 10

6. Attach a ground wire: a. Remove the nut from the Ground Bonding Point.b. Attach a ground wire (min. 8 AWG or 10 mm2) to the lug and replace the

Strany 11 - Configuration

Connecting Ethernet1. Turn the Cover Lock to the Unlocked icon. Slide the Port Cover down to remove it.2. Connect a TOUGHCable or other outdoor, s

Strany 13

4. Connect the other end of the Ethernet cable from the DATA port to the Ethernet port labeled POE on the GigE PoE Adapter.5. Connect an Ethernet ca

Strany 14

Below is a diagram of a finished installation with recommended surge protectors installed.Ground to Pole, Tower, or Grounding Block (Max. 1 m from Gr

Strany 15 - Hardware Installation

AlignmentTips• Fine-tuning is best achieved by a pair of installers with a dedicated, two-way communication link: one installer makes adjustments on

Strany 16 - Alignment Bracket

2. For the Master and Slave, ensure the Azimuth (AZ) and Elevation (EL) Adjustment Bolts are in the middle of their adjustmentranges.Elevation (EL)

Strany 17

5. Master Adjust the azimuth and elevation of the Master until the strongest received signal level is displayed on the LED Display of the Master.a.

Strany 18

Fine-Tuning the LinkThe Azimuth (AZ) and Elevation (EL) Adjustment Bolts of the Alignment Bracket adjust the azimuth and elevation within a range of ±

Strany 19 - Connecting Ethernet

There are three methods for determining the received signal level:• LED Display (described above)• airFiber Configuration Interface• Audio tone (op

Strany 20

SpecificationsairFiber AF-24Dimensions 649 x 426 x 303 mm (25.55 x 16.77 x 11.93")Weight 10.5 kg (23.15 lb) Mount IncludedOperating Frequency 24

Strany 21

Electrical Safety Information1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s l

Strany 22 - Alignment

Warranty ConditionsThe above warranty does not apply if the Product:(I) has been modified and/or altered, or an addition made thereto, except by Ubiq

Strany 23

IntroductionThank you for purchasing the Ubiquiti Networks® airFiber® 24GHz Point-to-Point Radio. This Quick Start Guide is designed to guide you thr

Strany 24

DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE

Strany 25 - Fine-Tuning the Link

NoteSome countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You

Strany 26

Industry CanadaCAN ICES-3(A)/NMB-3(A)This Class A digital apparatus complies with Canadian CAN ICES-3(A).To reduce potential radio interference to oth

Strany 27 - Specifications

CE MarkingCE marking on this product represents the product is in compliance with all directives that are applicable to it. This equipment is intended

Strany 28 - Limited Warranty

PHRRJL090514Magyar [Hungarian]Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ követelményekne

Strany 30 - Limitation of Liability

© 2012-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, EdgeRoute

Strany 31 - Compliance

Hardware OverviewSideAlignment BracketElevation AdjustmentAzimuth AdjustmentGround Bonding PointLock BoltsLock Bolts2airFiber® AF-24 Quick Start Guide

Strany 32 - RF Exposure Warning

BackLock BoltsLock BoltsAzimuth AdjustmentLock BoltsLock BoltsCover LockElevation AdjustmentPort Cover3Hardware Overview

Strany 33 - Declaration of Conformity

InterfacesRESET DATA AUX CONFIGLED DisplayInterface DescriptionRESETTo reset to factory defaults, press and hold the Reset button for more than five s

Strany 34 - PHRRJL090514

LED State StatusDATASpeedOff 10/100 MbpsOn 1000 MbpsLink/ActOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flashing Ethernet ActivityAUXGPSOff

Strany 35

Installation Requirements• 17 mm wrench• 13 mm socket wrench or driver• Clear line of sight between airFiber radios• Clear view of the sky for pro

Strany 36 - Downloads downloads.ubnt.com

• Once configuration is complete, disconnect the cables to move the airFiber radios.• Reconnect at the site. • After you have mounted the airFiber

Komentáře k této Příručce

Žádné komentáře