Ubiquiti Networks LiteStation2 Průvodce nastavením Strana 1

MANUAL AirOS

Current Status of the system bridge table • Show Bridge Table: selection lists all the entries in the system bridge table, while the device is opera

Current Status of the DHCP leases • Show DHCP Leases selection shows the current status of the leased IP addresses by the device’s DHCP server. Inte

Tools Tools: provides network utilities in pop-up window: Wireless link throughput estimation with Network Speed Test utility • Speed Test: This ut

Ping utility should be used for the preliminary link quality and packet latency estimation between two network devices using the ICMP packets. Remote

Antenna alignment Tool Antenna Alignment utility allows the installer to point and optimize the antenna in the direction of maximum link signal. The

2. Station WDS: WDS stands for Wireless Distribution System. Station WDS should be used while connecting to the Access Point which is operating in WDS

Auto option should be enabled in order to establish WDS connection between Access Points if WDS Peers are not specified (applicable for AP WDS mode on

network scans on the wireless stations. Control is available while operating in Access Point mode only. Lock to AP MAC: This allows the station to al

Drawback: It will reduce throughput proportional to the channel size reduction. So just as turbo mode (40MHz) increases possible speeds by 2x, half sp

Choose the security method according to the Access Point security policy. Subscriber station should be authorized by Access Point in order to get acce

Contents • 1 AirOS Introduction • 2 Configuration Guide o 2.1 Navigation o 2.2 Main Page  2.2.1 Status Reporting  2.2.2 Statistics Reporting 

For 64-bit – specify WEP key as 5 HEX (0-9, A-F or a-f) pairs (e.g. 00112233AA) or 5 ASCII characters. For 128-bit – specify WEP key as 13 HEX (0-9,

The Network Page allows the administrator to setup bridge or routing functionality. AirOS powered devices can operate in bridge or router mode. The I

address space. WLAN and LAN interfaces form the virtual bridge interface while acting as the bridge ports. The bridge has assigned IP settings for man

platform Utility should be started on the administrator PC which resides on the same network segment as the AirOS device. AirOS system will return to

Enable DHCP Server: Dynamic Host Configuration Protocol (DHCP) Server assigns IP addresses to clients who will associate to the wireless interface.

This page handles advanced routing and wireless settings. The Advanced options page allows you to manage advanced settings that influence on the devic

conservative rate algorithm provides the best case stability / robustness, but may compromise maximum throughput. The optimistic rate algorithm always

Acknowledgement Timeout AirOS has an auto-acknowledgement timeout algorithm which dynamically optimizes the acknowledgement timeout value without user

LED 1 (Red) will switch on if the RSSI reach the value set in an entry field next to it. LED 2 (Yellow) will switch on if the RSSI reach the value se

Ping WatchDog The ping watchdog sets the AirOS Device to continuously ping a user defined IP address (it can be the internet gateway for example). If

AirOS Introduction The design goal of AirOS was simplicity and power. Unlike previous and current market-leading wireless or router operating systems

Failure Count To Reboot: specify the number of ICMP “echo response” replies. If the specified number of ICMP “echo response” packets is not received c

Enable Telnet Server: Enables Telnet access to the AirOS Device. Server Port: Telnet service TCP/IP port setting. System The System Page contains Ad

Verify Password: re-enter the new password to verify its accuracy. Click Change button to save the changes. Router Protocol Host Name Host Name is

and click the Upload button. Close this window – cancel the upload process. After the new firmware image is uploaded into the system, use Upgrade butt

Note: the screen shots in this document represent PowerStation2 graphical user interface but they are also fully applicable for NanoStation2 and LiteS

The Main Page displays a summary of link status information, basic configuration settings of the device (operating mode, network settings), traffic st

Channel: This is the 802.11 channel number that corresponds to the operating frequency. Device uses the selected channel to transmit and receive data.

Note: LAN IP Address and WLAN IP Address displays the same value - current IP address of the virtual bridge interface, while the device is operating i

This statistics represents the total amount of unicast and broadcast IP data transfered between AirOS powered device and PPPoE server through the PPP

• Show Stations: selection lists the stations which are connected to the device while operating in Access Point mode. Statistics for all the stations